Search Criteria
Products meeting the search criteria
ACE V3 Xbox 360 Programming Board
The ACE V3 is a compact electronics board designed for use with compatible Xbox 360 motherboards during specialist servicing, development and motherboard programming work.
The board uses a revised 150MHz crystal together with an improved PCB layout designed to provide clean and stable signal performance.
Features
-
ACE V3 board revision
-
High-performance 150MHz crystal
-
Improved PCB layout
-
No solder bridges required
-
Quality electronic components
-
Compatible with Corona V1–V6 motherboards
-
Compact design suitable for electronics servicing
Package Contents
-
1 × ACE V3 Board
-
6 × Connection Wires
-
1 × Double-Sided Adhesive Pad
-
Optional 1 × Pin Header
Optional Programming Header
An optional pin header can be supplied for boards that do not already have one installed.
The header provides a convenient connection point for compatible programming hardware and can either be soldered permanently or temporarily held in position during servicing.
Please note: This product requires soldering and is intended for experienced electronics technicians.
ACE V3+ Xbox 360 Corona Programming Board
The ACE V3+ is a compact programming and interface board designed for use with compatible Xbox 360 Corona motherboards during specialist electronics servicing and motherboard work.
The board is supplied pre-configured for compatible Corona applications and can also be reprogrammed where required using suitable programming hardware.
Please note that the programming pinout differs slightly from some earlier board revisions, so the programming cable wiring may need to be adjusted depending on the programmer being used.
NAND Compatibility
Before carrying out motherboard servicing, check whether the console uses a:
-
16MB NAND
-
4GB NAND
Different NAND types require different reading and writing hardware.
A standard SPI programmer may be suitable for compatible 16MB NAND boards, while 4GB NAND motherboards require a dedicated 4GB-compatible read/write solution.
Motherboard Compatibility
Some Corona revisions may require an additional motherboard interface adapter depending on the board revision and available signal traces.
For reliable identification, the motherboard should be visually inspected before installation.
Important Information
-
Designed for compatible Xbox 360 Corona motherboards
-
Reprogrammable using suitable programming hardware
-
Compact PCB design
-
Different NAND revisions may require different programming tools
-
Additional interface hardware may be required on some motherboard revisions
-
Intended for experienced electronics technicians
-
Soldering is required
Aladdin XT Plus 2 Original Xbox Programmable Board
The Aladdin XT Plus 2, also known as xenoFX, is a compact programmable LPC-based board designed for compatible Original Xbox motherboard servicing, restoration and development work.
It features 256KB reflashable memory and supports compatible firmware images for technicians and enthusiasts working with Original Xbox hardware.
KEY FEATURES
• 256KB reflashable memory
• Compatible with Original Xbox v1.0–v1.6B
• LPC-based installation
• Two selectable operating modes
• Integrated status LED
• Female pin header fitted to PCB
• Separate male pin header included
• Compatible with optional LPC rebuild boards
• Suitable for motherboard restoration and development projects
LPC REBUILD SUPPORT
Original Xbox v1.6 and v1.6B motherboards may require an LPC rebuild before installation.
Compatible LPC rebuild QSBs are available separately to provide a cleaner, more consistent connection method.
FIRMWARE
The board can be programmed with compatible 256KB firmware images suitable for Original Xbox servicing and development applications.
Firmware compatibility should always be confirmed before flashing.
IMPORTANT INFORMATION
Incorrect programming may leave the board unable to boot until it is recovered using suitable programming equipment.
Only reflash the board if you are familiar with the recovery process.
COMPATIBILITY
• Original Xbox v1.0–v1.6B
PACKAGE CONTENTS
• 1 × Aladdin XT Plus 2 Programmable Board
• 1 × Male Pin Header
FreeRunner Xbox 360 Development Board
The ChipChopMod FreeRunner is an open-source electronics development board designed for compatible Xbox 360 motherboard servicing, development and signal-processing applications.
Built around the Altera MAX V CPLD, the FreeRunner provides a compact and programmable platform suitable for technicians, electronics developers and enthusiasts working with compatible Xbox 360 hardware.
Its clearly labelled connection points and open-source design make it particularly useful for motherboard development, repair projects and custom electronics work.
Key Features
- Altera MAX V CPLD
- Open-source hardware and firmware
- Programmable electronics platform
- Compatible with selected Xbox 360 Phat and Slim motherboards
- Clearly labelled solder points
- Compact PCB design
- High-quality components
- Suitable for development, servicing and custom electronics projects
Compatible Motherboard Families
Depending on firmware and project requirements, the board may be used with selected motherboard revisions including:
- Xenon
- Zephyr
- Falcon
- Jasper
- Tonasket
- Trinity
- Corona
- Waitsburg
- Stingray
Compatibility and additional hardware requirements vary depending on motherboard revision and intended application.
Package Contents
- 1 × ChipChopMod FreeRunner Development Board
Programming cables, connection wire and accessories are not included unless otherwise stated.
Important Information
- Intended for experienced electronics users
- Soldering is required
- Programming may be required
- Confirm motherboard compatibility before installation
- Suitable for legitimate repair, servicing and development work
Credits
- ArminAustin200 – Design and Development
- Octal450 – Development Assistance
- DrTrinity – Development Assistance
Matrix V1 Xbox 360 Programmable Development Board
The Matrix V1 is a compact programmable electronics board suitable for compatible Xbox 360 motherboard servicing, development and signal-testing applications.
This version is supplied without an onboard crystal oscillator, making it suitable for projects where an external or motherboard-derived clock source is required.
The compact PCB provides clearly accessible solder points and is designed for experienced technicians carrying out board-level electronics work.
Key Features
- Compact Matrix V1 PCB
- Supplied without onboard oscillator
- Programmable design
- Accessible signal connection points
- Suitable for selected Xbox 360 motherboard revisions
- Compatible with external programming hardware
- Optional capacitor available for selected applications
Compatible Motherboard Families
Depending on the intended project and firmware configuration, the board can be used with selected Xbox 360 motherboard families including:
- Xenon
- Zephyr
- Falcon
- Jasper
- Trinity
- Corona
Compatibility and connection requirements vary by motherboard revision.
Connection Points
- A – RST
- B – POST
- C – STBY_CLK
- F – EXT_CLK
These labelled pads provide convenient access to the relevant signals during electronics development and servicing.
Installation
Installation requires soldering between the board and compatible motherboard signal points.
Fine-gauge electronics wire is recommended for clean and reliable connections.
Package Contents
- 1 × Matrix V1 Development Board – Without Oscillator
- Optional capacitor if selected
Installation wire, adhesive and programming hardware are not included.
Important Information
This product is intended for experienced electronics users.
Programming, soldering and motherboard identification may be required before use.
Matrix V3 Xbox 360 Programmable Development Board
The Matrix V3 is a compact programmable electronics board suitable for compatible Xbox 360 motherboard servicing, development and signal-processing applications.
This version includes an onboard crystal oscillator, providing an integrated clock source for compatible electronics projects.
The board features clearly accessible connection pads and is intended for experienced technicians carrying out board-level repair, testing and development work.
Key Features
- Matrix V3 PCB
- Integrated crystal oscillator
- Programmable design
- Compact form factor
- Clearly accessible solder points
- Suitable for selected Xbox 360 motherboard revisions
- Compatible with external programming hardware
- Suitable for motherboard servicing and development
Compatible Motherboard Families
Depending on firmware and intended application, the board can be used with selected Xbox 360 motherboard families including:
- Falcon
- Jasper
- Trinity
- Corona
Compatibility and connection requirements vary depending on motherboard revision and intended use.
Connection Points
- A – RST
- B – POST
- C – STBY_CLK
- F – EXT_CLK
Installation
Installation requires soldering between the board and compatible motherboard signal points.
Fine-gauge electronics wire is recommended for clean and reliable connections.
Package Contents
- 1 × Matrix V3 Development Board
- Integrated Crystal Oscillator
Installation wire, adhesive and programming hardware are not included.
Important Information
This product is intended for experienced electronics users.
Programming, soldering and motherboard identification may be required before use.
Xecuter CoolRunner Rev C Programmable Board
The Xecuter CoolRunner Rev C is a compact programmable electronics board designed for compatible Xbox 360 motherboard development, diagnostics and servicing.
It provides accessible signal connection points and can be programmed with suitable timing configurations for supported motherboard revisions.
Key Features
- Compact programmable PCB
- Suitable for selected Xbox 360 motherboards
- Clearly labelled solder points
- Compatible with external programming hardware
- Suitable for development and diagnostic work
- Useful for legacy Xbox 360 servicing projects
Compatible Motherboard Families
Depending on configuration, the board may be used with selected:
- Falcon
- Jasper
- Trinity
- Corona
Installation
Installation requires:
- Soldering
- Correct motherboard identification
- Suitable programming hardware
- Appropriate firmware or timing configuration
This product is intended for experienced electronics users.
Package Contents
- 1 × Xecuter CoolRunner Rev C Board
XFlasher 360 Replacement Programming Cable Set
Replacement cable set for compatible XFlasher 360 programming and diagnostic hardware.
Ideal for replacing damaged, worn or missing cables used during motherboard servicing and development work.
Contents
- 1 × NAND Header Cable
- 1 × Programming Cable
- 1 × eMMC Cable
- 1 × Dupont Breakaway Crystal Connector
Key Features
- Replacement cable set for XFlasher 360
- Suitable for memory access and programming work
- Includes eMMC connectivity
- Useful for diagnostics, repair and development
- Ideal as a spare workshop cable set
Important Information
This listing is for the cable set only.
The programmer hardware is not included.
XFlasher 360 Rev C Development Programmer
The XFlasher 360 Rev C is an all-in-one programming and diagnostic interface for compatible Xbox 360 motherboards.
It combines support for traditional NAND access, 4GB eMMC storage and external programmable devices in a single compact tool.
Key Features
- Supports compatible 16MB NAND devices
- Integrated 4GB eMMC interface
- SPI and eMMC mode selection
- Fast memory read/write capability
- Integrated EEPROM
- FT reset button
- Native Windows x64 driver support
- Compatible with J-Runner with Extras
- Supplied with programming cables
- Suitable for diagnostics, development and motherboard servicing
Integrated 4GB eMMC Support
The XFlasher 360 includes built-in support for compatible 4GB Corona eMMC systems, removing the need for a separate SD card reader or additional memory programming tool.
Included Cables
Supplied with:
- NAND programming cable
- Device programming cable
- 4GB eMMC connection cable
Software Support
Designed for use with J-Runner with Extras, providing an integrated interface for compatible memory access and programming functions.
Compatibility
Suitable for compatible Xbox 360 motherboard revisions.
Connection method varies by board type, so correct motherboard identification is required before use.
Package Contents
- 1 × XFlasher 360 Rev C
- 1 × NAND Programming Cable
- 1 × Device Programming Cable
- 1 × 4GB eMMC Cable