Search Criteria
Products meeting the search criteria
ACE V3 Xbox 360 Programming Board
The ACE V3 is a compact electronics board designed for use with compatible Xbox 360 motherboards during specialist servicing, development and motherboard programming work.
The board uses a revised 150MHz crystal together with an improved PCB layout designed to provide clean and stable signal performance.
Features
-
ACE V3 board revision
-
High-performance 150MHz crystal
-
Improved PCB layout
-
No solder bridges required
-
Quality electronic components
-
Compatible with Corona V1–V6 motherboards
-
Compact design suitable for electronics servicing
Package Contents
-
1 × ACE V3 Board
-
6 × Connection Wires
-
1 × Double-Sided Adhesive Pad
-
Optional 1 × Pin Header
Optional Programming Header
An optional pin header can be supplied for boards that do not already have one installed.
The header provides a convenient connection point for compatible programming hardware and can either be soldered permanently or temporarily held in position during servicing.
Please note: This product requires soldering and is intended for experienced electronics technicians.
ACE V3+ Xbox 360 Corona Programming Board
The ACE V3+ is a compact programming and interface board designed for use with compatible Xbox 360 Corona motherboards during specialist electronics servicing and motherboard work.
The board is supplied pre-configured for compatible Corona applications and can also be reprogrammed where required using suitable programming hardware.
Please note that the programming pinout differs slightly from some earlier board revisions, so the programming cable wiring may need to be adjusted depending on the programmer being used.
NAND Compatibility
Before carrying out motherboard servicing, check whether the console uses a:
-
16MB NAND
-
4GB NAND
Different NAND types require different reading and writing hardware.
A standard SPI programmer may be suitable for compatible 16MB NAND boards, while 4GB NAND motherboards require a dedicated 4GB-compatible read/write solution.
Motherboard Compatibility
Some Corona revisions may require an additional motherboard interface adapter depending on the board revision and available signal traces.
For reliable identification, the motherboard should be visually inspected before installation.
Important Information
-
Designed for compatible Xbox 360 Corona motherboards
-
Reprogrammable using suitable programming hardware
-
Compact PCB design
-
Different NAND revisions may require different programming tools
-
Additional interface hardware may be required on some motherboard revisions
-
Intended for experienced electronics technicians
-
Soldering is required
FreeRunner Xbox 360 Development Board
The ChipChopMod FreeRunner is an open-source electronics development board designed for compatible Xbox 360 motherboard servicing, development and signal-processing applications.
Built around the Altera MAX V CPLD, the FreeRunner provides a compact and programmable platform suitable for technicians, electronics developers and enthusiasts working with compatible Xbox 360 hardware.
Its clearly labelled connection points and open-source design make it particularly useful for motherboard development, repair projects and custom electronics work.
Key Features
- Altera MAX V CPLD
- Open-source hardware and firmware
- Programmable electronics platform
- Compatible with selected Xbox 360 Phat and Slim motherboards
- Clearly labelled solder points
- Compact PCB design
- High-quality components
- Suitable for development, servicing and custom electronics projects
Compatible Motherboard Families
Depending on firmware and project requirements, the board may be used with selected motherboard revisions including:
- Xenon
- Zephyr
- Falcon
- Jasper
- Tonasket
- Trinity
- Corona
- Waitsburg
- Stingray
Compatibility and additional hardware requirements vary depending on motherboard revision and intended application.
Package Contents
- 1 × ChipChopMod FreeRunner Development Board
Programming cables, connection wire and accessories are not included unless otherwise stated.
Important Information
- Intended for experienced electronics users
- Soldering is required
- Programming may be required
- Confirm motherboard compatibility before installation
- Suitable for legitimate repair, servicing and development work
Credits
- ArminAustin200 – Design and Development
- Octal450 – Development Assistance
- DrTrinity – Development Assistance
JR Programmer V2
The JR Programmer V2 is a compact USB programming tool designed for Xbox 360 NAND reading, writing and motherboard servicing.
It provides fast access to compatible Xbox 360 NAND devices and is suitable for repair technicians, electronics enthusiasts and users carrying out board-level diagnostics or firmware recovery work.
A pin header is included to make connection to compatible boards easier.
Key Features
- Fast Xbox 360 NAND reading and writing
- Compatible with selected Xbox 360 Phat and Slim consoles
- Suitable for motherboard servicing and diagnostics
- Compatible with NAND-X QSB accessories
- Supports POST monitoring
- Onboard power and data LEDs
- Firmware upgrade support
- Designed for use with J-Runner
- Compact and reusable programming tool
USB Connection
A Mini USB cable is required to connect the JR Programmer V2 to your computer.
Please note this uses Mini USB, not Micro USB or USB-C.
USB cable is not included.
Important Usage Information
The exposed pins on the underside of the programmer must not be allowed to touch conductive metal surfaces while powered, as this could short the board and cause permanent damage.
We recommend insulating the underside using Kapton tape, suitable electrical insulation tape or a non-conductive enclosure.
Bootloader Mode
The programmer may occasionally remain in bootloader mode after using the onboard mode switch.
If the status LED remains permanently red and the programmer is no longer operating normally, the firmware may need to be reflashed.
This can be carried out using J-Runner, which includes compatible JR Programmer firmware.
Package Contents
- 1 × JR Programmer V2
- 1 × NAND Read/Write Cable
- 1 × Programming Cable
- 1 × Pin Header
Please note: Mini USB cable is not included.
Matrix V1 Xbox 360 Programmable Development Board
The Matrix V1 is a compact programmable electronics board suitable for compatible Xbox 360 motherboard servicing, development and signal-testing applications.
This version is supplied without an onboard crystal oscillator, making it suitable for projects where an external or motherboard-derived clock source is required.
The compact PCB provides clearly accessible solder points and is designed for experienced technicians carrying out board-level electronics work.
Key Features
- Compact Matrix V1 PCB
- Supplied without onboard oscillator
- Programmable design
- Accessible signal connection points
- Suitable for selected Xbox 360 motherboard revisions
- Compatible with external programming hardware
- Optional capacitor available for selected applications
Compatible Motherboard Families
Depending on the intended project and firmware configuration, the board can be used with selected Xbox 360 motherboard families including:
- Xenon
- Zephyr
- Falcon
- Jasper
- Trinity
- Corona
Compatibility and connection requirements vary by motherboard revision.
Connection Points
- A – RST
- B – POST
- C – STBY_CLK
- F – EXT_CLK
These labelled pads provide convenient access to the relevant signals during electronics development and servicing.
Installation
Installation requires soldering between the board and compatible motherboard signal points.
Fine-gauge electronics wire is recommended for clean and reliable connections.
Package Contents
- 1 × Matrix V1 Development Board – Without Oscillator
- Optional capacitor if selected
Installation wire, adhesive and programming hardware are not included.
Important Information
This product is intended for experienced electronics users.
Programming, soldering and motherboard identification may be required before use.
Matrix V3 Xbox 360 Programmable Development Board
The Matrix V3 is a compact programmable electronics board suitable for compatible Xbox 360 motherboard servicing, development and signal-processing applications.
This version includes an onboard crystal oscillator, providing an integrated clock source for compatible electronics projects.
The board features clearly accessible connection pads and is intended for experienced technicians carrying out board-level repair, testing and development work.
Key Features
- Matrix V3 PCB
- Integrated crystal oscillator
- Programmable design
- Compact form factor
- Clearly accessible solder points
- Suitable for selected Xbox 360 motherboard revisions
- Compatible with external programming hardware
- Suitable for motherboard servicing and development
Compatible Motherboard Families
Depending on firmware and intended application, the board can be used with selected Xbox 360 motherboard families including:
- Falcon
- Jasper
- Trinity
- Corona
Compatibility and connection requirements vary depending on motherboard revision and intended use.
Connection Points
- A – RST
- B – POST
- C – STBY_CLK
- F – EXT_CLK
Installation
Installation requires soldering between the board and compatible motherboard signal points.
Fine-gauge electronics wire is recommended for clean and reliable connections.
Package Contents
- 1 × Matrix V3 Development Board
- Integrated Crystal Oscillator
Installation wire, adhesive and programming hardware are not included.
Important Information
This product is intended for experienced electronics users.
Programming, soldering and motherboard identification may be required before use.
The Viper Triple NAND is an advanced programmable development board for compatible Xbox 360 motherboards, allowing up to three separate NAND configurations to be stored and selected from one system.
It is designed for development, diagnostics, firmware testing and advanced motherboard servicing.
Key Features
- Three separate NAND configurations
- Compact QSB design
- Minimal wiring
- No trace cutting required
- Compatible with selected 16MB Xbox 360 motherboards
- NAND selection using the console sync button
- Windows utility support
- Suitable for development and diagnostic work
Compatibility
Designed for selected:
- 16MB Jasper motherboards
- Compatible Xbox 360 Slim motherboards
- Other supported boards with suitable adapters
Installation
Installation requires soldering, motherboard identification and NAND programming experience.
This product is intended for experienced electronics users and developers.
Important Information
Always create verified NAND backups before making changes.
Incorrect programming or installation may prevent the system from booting.
Xbox 360 Corona Postfix Adapter V1
The Corona Postfix Adapter V1 is designed for compatible Xbox 360 Slim Corona V3 and V4 motherboards where the standard POST_OUT connection is not available through the motherboard trace.
The adapter fits around the CPU area and provides access to the required signal point from underneath the processor, giving technicians a clean connection option during motherboard servicing and diagnostic work.
Compact V1 Design
This V1 revision uses a smaller PCB footprint than some later adapter designs, making it a neat solution where only the required signal connection is needed.
For this version, the POST_1 pad is the relevant connection point.
Compatibility
- Xbox 360 Slim
- Corona V3 motherboards
- Corona V4 motherboards
- Suitable for specialist motherboard servicing
- Designed for boards where the standard POST_OUT trace is unavailable
Key Features
- Provides access to the POST_OUT signal
- Designed for compatible Corona V3/V4 motherboards
- Compact V1 PCB design
- Fits around the CPU area
- Useful for motherboard diagnostics and signal access
- Simple connection via the POST_1 pad
Please note: Installation requires console disassembly and soldering. This product is intended for users with suitable electronics repair experience.
Xbox 360 Trinity Internal USB Storage Adapter
This internal USB adapter is designed for compatible Xbox 360 Trinity motherboards and uses the connection normally occupied by the original internal 4GB memory module.
Once installed, it provides an internal USB connection that can be used with compatible USB storage devices, helping keep the console’s external USB ports free.
Key Features
- Designed for Xbox 360 Trinity motherboards
- Replaces the original internal 4GB memory module connection
- Provides an internal USB connection
- Suitable for compatible USB flash drives
- Can be used with compatible USB storage devices and adapters
- Keeps external USB ports available
- Useful for console servicing and storage expansion
Installation
The adapter is fitted inside the console.
If an internal 4GB memory module is already installed, the existing module or header must be removed before fitting the adapter.
Console disassembly and soldering are required.
Compatibility
- Xbox 360 Trinity motherboards
- Compatible USB flash storage
- Compatible USB hard drives when used with suitable adapters
Storage support can vary depending on the console configuration and the device being used.
Important Information
- Intended for Trinity motherboards only
- Internal console access is required
- Professional installation is recommended
- Additional adapters may be required for some storage devices
- USB storage device is not included
Package Contents
- 1 × Xbox 360 Trinity Internal USB Storage Adapter