Search Criteria
Products meeting the search criteria
ACE V3 Xbox 360 Programming Board
The ACE V3 is a compact electronics board designed for use with compatible Xbox 360 motherboards during specialist servicing, development and motherboard programming work.
The board uses a revised 150MHz crystal together with an improved PCB layout designed to provide clean and stable signal performance.
Features
-
ACE V3 board revision
-
High-performance 150MHz crystal
-
Improved PCB layout
-
No solder bridges required
-
Quality electronic components
-
Compatible with Corona V1–V6 motherboards
-
Compact design suitable for electronics servicing
Package Contents
-
1 × ACE V3 Board
-
6 × Connection Wires
-
1 × Double-Sided Adhesive Pad
-
Optional 1 × Pin Header
Optional Programming Header
An optional pin header can be supplied for boards that do not already have one installed.
The header provides a convenient connection point for compatible programming hardware and can either be soldered permanently or temporarily held in position during servicing.
Please note: This product requires soldering and is intended for experienced electronics technicians.
Deluxe NAND-X & JR Programmer Cable
A reusable NAND programming cable designed for use with compatible NAND-X and JR Programmer hardware.
Each cable is hand assembled and fitted with Dupont male crimps on the ends, giving a clean and reliable connection without the need to repeatedly strip, trim or rework bare wire ends.
This makes the cable especially useful for technicians carrying out multiple NAND read/write jobs, where a durable and reusable connection is preferable to temporary wiring.
Key Features
- Compatible with suitable NAND-X and JR Programmer setups
- Designed for NAND reading and writing
- Hand assembled
- Dupont male crimps fitted to the cable ends
- Reusable across multiple jobs
- Helps provide a secure and consistent connection
- Supplied with heat-shrink tubing for additional insulation where required
- Suitable for both occasional users and experienced technicians
Ideal for Repeated Use
Unlike basic bare-ended wiring, the fitted crimps help reduce wear on the cable ends and make repeated connection much easier.
The supplied heat-shrink tubing can be positioned where required and shrunk into place to help protect and tidy the cable assembly.
Please note: Programming hardware is not included. Compatibility should be checked with your programmer and target board before use.
JR Programmer V2
The JR Programmer V2 is a compact USB programming tool designed for Xbox 360 NAND reading, writing and motherboard servicing.
It provides fast access to compatible Xbox 360 NAND devices and is suitable for repair technicians, electronics enthusiasts and users carrying out board-level diagnostics or firmware recovery work.
A pin header is included to make connection to compatible boards easier.
Key Features
- Fast Xbox 360 NAND reading and writing
- Compatible with selected Xbox 360 Phat and Slim consoles
- Suitable for motherboard servicing and diagnostics
- Compatible with NAND-X QSB accessories
- Supports POST monitoring
- Onboard power and data LEDs
- Firmware upgrade support
- Designed for use with J-Runner
- Compact and reusable programming tool
USB Connection
A Mini USB cable is required to connect the JR Programmer V2 to your computer.
Please note this uses Mini USB, not Micro USB or USB-C.
USB cable is not included.
Important Usage Information
The exposed pins on the underside of the programmer must not be allowed to touch conductive metal surfaces while powered, as this could short the board and cause permanent damage.
We recommend insulating the underside using Kapton tape, suitable electrical insulation tape or a non-conductive enclosure.
Bootloader Mode
The programmer may occasionally remain in bootloader mode after using the onboard mode switch.
If the status LED remains permanently red and the programmer is no longer operating normally, the firmware may need to be reflashed.
This can be carried out using J-Runner, which includes compatible JR Programmer firmware.
Package Contents
- 1 × JR Programmer V2
- 1 × NAND Read/Write Cable
- 1 × Programming Cable
- 1 × Pin Header
Please note: Mini USB cable is not included.