Search Criteria
Products meeting the search criteria
ACE V3 Xbox 360 Programming Board
The ACE V3 is a compact electronics board designed for use with compatible Xbox 360 motherboards during specialist servicing, development and motherboard programming work.
The board uses a revised 150MHz crystal together with an improved PCB layout designed to provide clean and stable signal performance.
Features
-
ACE V3 board revision
-
High-performance 150MHz crystal
-
Improved PCB layout
-
No solder bridges required
-
Quality electronic components
-
Compatible with Corona V1–V6 motherboards
-
Compact design suitable for electronics servicing
Package Contents
-
1 × ACE V3 Board
-
6 × Connection Wires
-
1 × Double-Sided Adhesive Pad
-
Optional 1 × Pin Header
Optional Programming Header
An optional pin header can be supplied for boards that do not already have one installed.
The header provides a convenient connection point for compatible programming hardware and can either be soldered permanently or temporarily held in position during servicing.
Please note: This product requires soldering and is intended for experienced electronics technicians.
0.1mm Enamelled Trace Repair Wire
High-quality 0.1mm enamelled copper wire designed for fine PCB trace repair, jumper wiring and delicate electronics work.
Its very small diameter makes it ideal for repairing damaged or lifted circuit traces where standard hookup wire would be too large.
Suitable For
-
PCB trace repair
-
Lifted or broken pad repair
-
Fine jumper wiring
-
Motherboard repair
-
Console repair
-
HDMI and connector repair
-
SMD and micro-soldering work
-
General electronics servicing
Key Features
-
0.1mm diameter
-
Fine enamelled copper construction
-
Suitable for precision board-level repair
-
Easy to route around small components
-
Ideal for restoring damaged PCB traces
-
Useful for both professional technicians and experienced hobbyists
Using Enamelled Repair Wire
The enamel coating provides electrical insulation while keeping the overall wire extremely thin.
Before soldering, the enamel must be removed from the section of wire being terminated. This can be done using a suitable stripping method or by carefully tinning the wire depending on the insulation type.
Package Contents
-
1 × Length / Reel of 0.1mm Trace Repair Wire
<p><h3>Xbox 360 Corona 4GB USB NAND Tool</h3> <p>The <strong>4GB USB Tool</strong> is designed for reading and writing the NAND on <strong>Xbox 360 Corona motherboards fitted with 4GB NAND storage</strong>.</p> <p>The tool features a built-in card reader, removing the need to source a separate compatible SD card reader to communicate with the NAND. It is designed to work with <strong>4GB NAND variant Corona motherboards</strong> and provides a straightforward solution for technicians carrying out motherboard servicing and NAND recovery work.</p> <p>It can be used as part of the repair process where NAND data has become corrupted or failed, helping technicians restore affected consoles and potentially return otherwise unusable hardware to service.</p> <p>For installers and repair technicians working on multiple consoles, replacement <strong>right-angle motherboard pin headers</strong> are also available separately as consumable items.</p> <p>Available in the <strong>UK and Europe exclusively from ChipChopMod</strong>.</p> <h3>Package Contents</h3> <ul> <li>1 × 4GB USB Tool</li> <li>1 × USB Tool Cable</li> <li>1 × Motherboard Pin Header</li> <li>1 × USB Tool Pin Header</li> </ul> <p><strong>Please note:</strong> Installation requires soldering and is intended for users with suitable electronics repair experience.</p></p>
ACE V3+ Xbox 360 Corona Programming Board
The ACE V3+ is a compact programming and interface board designed for use with compatible Xbox 360 Corona motherboards during specialist electronics servicing and motherboard work.
The board is supplied pre-configured for compatible Corona applications and can also be reprogrammed where required using suitable programming hardware.
Please note that the programming pinout differs slightly from some earlier board revisions, so the programming cable wiring may need to be adjusted depending on the programmer being used.
NAND Compatibility
Before carrying out motherboard servicing, check whether the console uses a:
-
16MB NAND
-
4GB NAND
Different NAND types require different reading and writing hardware.
A standard SPI programmer may be suitable for compatible 16MB NAND boards, while 4GB NAND motherboards require a dedicated 4GB-compatible read/write solution.
Motherboard Compatibility
Some Corona revisions may require an additional motherboard interface adapter depending on the board revision and available signal traces.
For reliable identification, the motherboard should be visually inspected before installation.
Important Information
-
Designed for compatible Xbox 360 Corona motherboards
-
Reprogrammable using suitable programming hardware
-
Compact PCB design
-
Different NAND revisions may require different programming tools
-
Additional interface hardware may be required on some motherboard revisions
-
Intended for experienced electronics technicians
-
Soldering is required
Aladdin XT Plus 2 Original Xbox Programmable Board
The Aladdin XT Plus 2, also known as xenoFX, is a compact programmable LPC-based board designed for compatible Original Xbox motherboard servicing, restoration and development work.
It features 256KB reflashable memory and supports compatible firmware images for technicians and enthusiasts working with Original Xbox hardware.
KEY FEATURES
• 256KB reflashable memory
• Compatible with Original Xbox v1.0–v1.6B
• LPC-based installation
• Two selectable operating modes
• Integrated status LED
• Female pin header fitted to PCB
• Separate male pin header included
• Compatible with optional LPC rebuild boards
• Suitable for motherboard restoration and development projects
LPC REBUILD SUPPORT
Original Xbox v1.6 and v1.6B motherboards may require an LPC rebuild before installation.
Compatible LPC rebuild QSBs are available separately to provide a cleaner, more consistent connection method.
FIRMWARE
The board can be programmed with compatible 256KB firmware images suitable for Original Xbox servicing and development applications.
Firmware compatibility should always be confirmed before flashing.
IMPORTANT INFORMATION
Incorrect programming may leave the board unable to boot until it is recovered using suitable programming equipment.
Only reflash the board if you are familiar with the recovery process.
COMPATIBILITY
• Original Xbox v1.0–v1.6B
PACKAGE CONTENTS
• 1 × Aladdin XT Plus 2 Programmable Board
• 1 × Male Pin Header
JR Programmer V2
The JR Programmer V2 is a compact USB programming tool designed for Xbox 360 NAND reading, writing and motherboard servicing.
It provides fast access to compatible Xbox 360 NAND devices and is suitable for repair technicians, electronics enthusiasts and users carrying out board-level diagnostics or firmware recovery work.
A pin header is included to make connection to compatible boards easier.
Key Features
- Fast Xbox 360 NAND reading and writing
- Compatible with selected Xbox 360 Phat and Slim consoles
- Suitable for motherboard servicing and diagnostics
- Compatible with NAND-X QSB accessories
- Supports POST monitoring
- Onboard power and data LEDs
- Firmware upgrade support
- Designed for use with J-Runner
- Compact and reusable programming tool
USB Connection
A Mini USB cable is required to connect the JR Programmer V2 to your computer.
Please note this uses Mini USB, not Micro USB or USB-C.
USB cable is not included.
Important Usage Information
The exposed pins on the underside of the programmer must not be allowed to touch conductive metal surfaces while powered, as this could short the board and cause permanent damage.
We recommend insulating the underside using Kapton tape, suitable electrical insulation tape or a non-conductive enclosure.
Bootloader Mode
The programmer may occasionally remain in bootloader mode after using the onboard mode switch.
If the status LED remains permanently red and the programmer is no longer operating normally, the firmware may need to be reflashed.
This can be carried out using J-Runner, which includes compatible JR Programmer firmware.
Package Contents
- 1 × JR Programmer V2
- 1 × NAND Read/Write Cable
- 1 × Programming Cable
- 1 × Pin Header
Please note: Mini USB cable is not included.
Matrix V1 Xbox 360 Programmable Development Board
The Matrix V1 is a compact programmable electronics board suitable for compatible Xbox 360 motherboard servicing, development and signal-testing applications.
This version is supplied without an onboard crystal oscillator, making it suitable for projects where an external or motherboard-derived clock source is required.
The compact PCB provides clearly accessible solder points and is designed for experienced technicians carrying out board-level electronics work.
Key Features
- Compact Matrix V1 PCB
- Supplied without onboard oscillator
- Programmable design
- Accessible signal connection points
- Suitable for selected Xbox 360 motherboard revisions
- Compatible with external programming hardware
- Optional capacitor available for selected applications
Compatible Motherboard Families
Depending on the intended project and firmware configuration, the board can be used with selected Xbox 360 motherboard families including:
- Xenon
- Zephyr
- Falcon
- Jasper
- Trinity
- Corona
Compatibility and connection requirements vary by motherboard revision.
Connection Points
- A – RST
- B – POST
- C – STBY_CLK
- F – EXT_CLK
These labelled pads provide convenient access to the relevant signals during electronics development and servicing.
Installation
Installation requires soldering between the board and compatible motherboard signal points.
Fine-gauge electronics wire is recommended for clean and reliable connections.
Package Contents
- 1 × Matrix V1 Development Board – Without Oscillator
- Optional capacitor if selected
Installation wire, adhesive and programming hardware are not included.
Important Information
This product is intended for experienced electronics users.
Programming, soldering and motherboard identification may be required before use.
Matrix V3 Xbox 360 Programmable Development Board
The Matrix V3 is a compact programmable electronics board suitable for compatible Xbox 360 motherboard servicing, development and signal-processing applications.
This version includes an onboard crystal oscillator, providing an integrated clock source for compatible electronics projects.
The board features clearly accessible connection pads and is intended for experienced technicians carrying out board-level repair, testing and development work.
Key Features
- Matrix V3 PCB
- Integrated crystal oscillator
- Programmable design
- Compact form factor
- Clearly accessible solder points
- Suitable for selected Xbox 360 motherboard revisions
- Compatible with external programming hardware
- Suitable for motherboard servicing and development
Compatible Motherboard Families
Depending on firmware and intended application, the board can be used with selected Xbox 360 motherboard families including:
- Falcon
- Jasper
- Trinity
- Corona
Compatibility and connection requirements vary depending on motherboard revision and intended use.
Connection Points
- A – RST
- B – POST
- C – STBY_CLK
- F – EXT_CLK
Installation
Installation requires soldering between the board and compatible motherboard signal points.
Fine-gauge electronics wire is recommended for clean and reliable connections.
Package Contents
- 1 × Matrix V3 Development Board
- Integrated Crystal Oscillator
Installation wire, adhesive and programming hardware are not included.
Important Information
This product is intended for experienced electronics users.
Programming, soldering and motherboard identification may be required before use.